Especially the girl characters, a morbidly obese whale, a granny, some fat arse bird girl and a gross looked redhead with gross **** all over her. I think its mainly the characters, honestly they suck. Ive had Bleeding edge installed since it launched and really have not been enjoying it every time I try it. I feel bad for Xbox and think they need to steep in and get these devs making games people want, like a Horizon 2 or God of War. Depress lever so that the pads contact the rotor correctly and adjust caliper position if necessary.Why do these developers do this to Xbox and Microsoft? Xbox invests in them, gives them a blank check and free reign to make something Why do these developers do this to Xbox and Microsoft? Xbox invests in them, gives them a blank check and free reign to make something amazing and this Bleeding Edge crap is what they produce. Remove bleed block, fit brake pads and wheel. Clean lever and caliper with brake cleaner or isopropyl alcohol to ensure all excess oil is removed.ġ4. Remove caliper syringe by pulling on the Bleeding Edge tool don’t turn the tool. Now remove lever syringe and refit bleed port screw being careful of spilling fluid. Press on lever syringe plunger, then release and close syringe tube clamp. Top tip: If the oil exiting the system is dark and dirty, then you should repeat the bleed process until the oil in the system is clear.ġ1. Repeat until minimal bubbles are visible in lever syringe tube. Pull on lever syringe to create a vacuum, then press down on syringe to pressurise system. Turn bleeding edge tool clockwise until it stops to close system.ġ0. Stop before air enters system at the caliper.ĩ. Push up on the lever syringe to draw fluid back up from the caliper syringe. Open lever syringe clamp, then holding vertically, gently push plunger down to insert all oil and stop before air enters system.Ĩ. Turn bleeding edge tool one turn anti-clockwise to open system.ħ. Insert Bleeding Edge tool in to hole, and push in until you feel and hear a snap.Ħ. Remove rubber caliper bleed plug by hand. Thread and nip tight the ¾ full lever syringe into lever bleed port.ĥ. Remove lever bleed port screw using Torx T10 and place to one side. Adjust brake lever position so the tip of the lever is 75-80mm from the centre line of the handlebar.Ĥ. Top tip: When filling syringes, make sure the tube end is fully submerged in oil to prevent any air bubbles entering.ģ. Fill lever syringe ¾ full of brake fluid and close syringe clamp. Add small amount of DOT 5.1 brake fluid to caliper syringe. Fit lever bleed tool and Bleeding Edge tool to syringes. Fit bleed block to caliper and turn pad contact adjuster in opposite direction of arrow until it stops.Ģ. It can actually strip paint, so wipe away any spillage as quick as possible! Also ensure you have removed all remnants of brake fluid before fitting the brake pads and wheel back in to position, the smallest amount of oil will contaminate the braking surfaces and is almost impossible to remove.ġ. It’s recommended that you wear nitrile gloves when handling DOT brake fluid due to its corrosive properties. SRAM brakes that use Bleeding Edge also have an improved oil path through the caliper to further help with the bleeding process – all the compatible models can be found on the SRAM website. The Bleeding Edge tool also allows the caliper bleed port to be closed off before the syringe is removed, eliminating oil spillage and reducing clean up. It’s simple and incredibly easy to fit and gives a defined snap to tell you it is correctly inserted in place. The idea is to reduce the amount of fuss and mess when carrying out a successful brake bleed.īy utilising a quick and simple pop on/off bleed-port interface, Bleeding Edge minimises the chance of air sneaking in to the system. Most new SRAM disc brakes are designed with a specific bleed port in the caliper to be used with a Bleeding Edge tool.
0 Comments
Leave a Reply. |